MLG2000AWW Maytag Washer Dryer Combo - Overview

The drum support roller (Dryer Drum Support Roller, Drum Roller and Washer Assembly) holds the drum in the proper position while it spins on the support wheels. This part rotates on the roller shaft w.

This thermostat (Dryer Operating Thermostat, Dryer Cycling Thermostat, Cycling Thermostat, Dryer Thermostat) is used to maintain a temperature of 155 degrees in the dryer drum. The internal bias heate.

When the igniter reaches a high enough temperature, these coils (Coil Valve, Dryer Gas Valve Coil Kit, Dryer Valve Coil Kit, Gas Valve Solenoid) work together to open the gas valve and allow the gas t.

The front glide is located at the front of the dryer, the drum rides along it. If you hear a metal-on-metal noise when your dryer is running, your front glide may be worn out and require replacing. Th.

This roller shaft is also known as a support roller shaft or a drum roller axle, and is a part for your dryer. The function of this piece is to act as the axle for the drum roller; it provides a place.

This multi rib belt spins the dryer drum during the drying cycle. This belt is 91-5/8 inches in length, 3/8th of an inch wide and has five ridges. It is black in color and made of rubber. You may need.

This is a replacement lint filter for your dryer. The lint filter is approximately 12 1/2 inches in length. Simply remove the existing filter and replace it with the new one. Check for an excess build.

This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter.

The idler pulley tightens the drive belt to properly spin the dryer drum. It is attached to an idler bracket. This part comes with the idler pulley and center bearing. To replace this part, you will n.

If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor if it is hot enough .

If you notice that your dryer is noisy or will not tumble, then you may need to replace the drum roller shaft washer. This drum roller shaft washer is just under an inch in diameter and is sold indivi.

This flat style igniter comes with a wire harness connector. This part ignites the gas within the dryer. Bracket is NOT included.

Questions And Answers for MLG2000AWW

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!

The washer started leaking. Checked the hoses. Everything is in good condition and they are dry. What might be the problem?

Hi Anna, Thank you for your question. If the washer is leaking, there are some parts that you will need to check to see which one is causing the issue. You will need to check the hoses, the pump, the tub cover gasket, the water inlet valve, the bellow or door boot seal, the water level switch, the door catch and the tub seal. We hope this helps. Thank you and have a great day!

I push the start button for the washer and sometimes it shuts off within a minute and the door doesn,t lock and other times it will shut off mid way through the first cycle.What should i do?

Hello and thank you for writing. It certainly sounds like it could be a faulty door switch PS1964648 and/or possibly a malfunctioning door lock switch PS11739335 you should check the part(s) for signs of damage or test with a multimeter, and replace the part(s) as needed. We hope this helps. Please contact us anytime if you require further assistance.

Where is electronic control board ps11739517 located in this unit? What picture on your unit overview is this part located.

Hello Tom, thank you for your question. This electronic control board is located in the cabinet front dryer section. The link to the diagram is attached, please refer to diagram number 22. We hope this information is useful.

Hi Merrill, thank you for getting in touch. Based on the description that you have provided, we would recommend checking the inlet hose for any blockage or damage. If that is not causing the issue, then the water inlet valve part number, PS11739363, is most likely faulty and may need to be replaced. We hope this helps!

Hola Óscar, gracias por comunicarte. El tablero de control electrónico para este modelo aparece como número de selección de pieza PS11741047. ¡Buena suerte con la reparación!

Common Symptoms of the MLG2000AWW

Show All

Show All

Show All

Show All

Show All

Show All

Show All

Show All

Show All

Show All

Show All

Show All

Show All

Show All

Show All

Videos related to models starting with MLG2000AWW

Replacing the Drum Support Roller Kit

Replacing the Dryer Cycling Thermostat

Replacing the Front Glide Kit

Replacing the Roller Shaft

Replacing the Multi Rib Belt - 91-5/8 Inches

Replacing the Retaining Ring

Replacing the Idler Pulley Wheel and Bearing

Replacing the Idler Pulley Wheel and Bearing

Installation Instructions of parts on the MLG2000AWW

first, I unplug the power supply of the dryer then I removed the two screws at the bottom of the dryer then pulled out the front part of the dryer,unplugged the blue & yellow wire for the on/off switch for the door,at the back of the dryer I unscrew the pannel for the belt,disconect the belt,and I unscrew the four screws on both side of t . Read more he front pannel to remove the front cover of the drum. Once I removed the front cover of the drum I can now remove the drum itself to access the drum support roller. I unscrew the rollers then replace it with the new once. It was an easy job.
Thank you.